Guitar Of The Month – October, 2025

Written by: Kevin Strom On: Nov 6th, 2025

Congratulations goes out to John Sheridan for his guitar build, to earn him Guitar of the Month for October, 2025.

John used our APK-10 kit as the basis to create his guitar.

“I recently went to Ireland where I purchased a beautiful Celtic guitar strap. Having no guitar that the strap suited, I purchased the parlour guitar kit from solo guitars. I had a clear vision of what I wanted my Celtic guitar to look like. I acquired: rhinestone shamrocks, a piezo pick up, a pair of black guitar strap buttons and a bone bridge & nut, as items that would be added to the initial kit.

The guitar strap would eventually be attached to the base of the guitar; however, I also wanted it to be attached to the top shoulder of the guitar. To support the guitar strap button on the shoulder. I had to take a piece of one by one pine, shape it to the interior contour of the shoulder and glue it in place inside the guitar’s body. 

The body and neck received a gentle sand of 220 sandpaper.

Performing a rough fit of the guitar‘s neck, I then used the sides of the neck to position where the saddle would be glued as outlined in the solo instruction manual (the side to side placement). Knowing that the scale length of the high E string was 25.5 inches and that the low E string would be just 2 mm longer, I calculated where the saddle should be placed (the front to back placement). Having removed the masking tape provided by the kit, I then placed my own masking tape where I believe the saddle should be glued, making sure it was a 1/32” smaller than the actual saddle.

The ends of the neck were checked for sharpness and filed back where necessary. 

Now, where I did not want paint to land was masking taped off: the bindings, the saddle, the rosette, the shamrocks, the fret board, and all the connection points for the neck to the body. The soundhole also was blocked off.

Using an airbrush, the body and neck got sprayed with a coat of white as a base. The area around the sound hole received a coat of yellow. Next the guitar and neck received a base coat of green while blending into the yellow around the sound hole. A pearlescent green was the final green coat and it also transitioned into the yellow around the sound hole. A “burn in” of black was sprayed to all the edges of the guitar body, sides of the neck, and head stock. A stencil of a Celtic braid was created, and sprayed black consecutively along the side of the guitar. Likewise, a stencil of a Celtic knot was created and sprayed black on the back of the guitar. The edges of both the braid and the knot were hand painted with gold to highlight the image.  My initials of a J and an S in the shape of a dragon were spray-painted in gold to the back of the head stock.

I removed the masking tape from the banding and from the rosette, and scraped away any “bleed through” from the masking tape. The rosette was in bad shape (too much “bleed through”), and so I touched up the design over the design provided.

Eight coats of Saman gloss varnish were applied to the body and the neck. These were allowed to cure for two weeks.

When it came time to remove the masking tape from the neck joints, the frets, the shamrocks, and the saddle, I took an X-Acto blade and gently scored the outline of the masking tape, so as not to accidentally remove any lacquer that might’ve come away with the tape.

Following the instructions in the solo manual, I created culls for both the neck attachment and the saddle attachment in preparation for their gluing. The neck was glued and clamped in place, as well as the nut.

24 hours later, the tuning machines were added. Using the method listed above, I double checked the exact placement of the saddle, then glued and clamped it in place.

 The rhinestone shamrocks were glued in place at this time as well as the strap buttons. 

24 hours later, having removed the clamps, I drilled out the holes for the string pegs, as well as the hole in the saddle for the piezo pick up. Having carefully measured the holes required for the pickups, amplifier and battery compartment, I proceeded to cover the areas with masking tape, mark the holes, and cut them out using a Dremel with a cutting wheel. Securing the electrical components with the screws included, I proceeded to place the bone bridge over the piezo pick up in the saddle slot. Because of the thickness of the piezo pick up, the saddle had to be sanded down by at least an 1/8”. I made my own jig out of two pieces of hardwood to clamp the bridge in place while I proceeded to sand down (on a flat surface) the excess material.

I purchased a set of no. 10 acoustic strings and proceeded to string the guitar up. It did require a little more sanding of the bridge and nut slots, as well as some trust rod adjustments to get the action to a comfortable level, but I am very pleased now as to how it sounds and plays both amplified and acoustically.”

– John Sheridan

One response to “Guitar Of The Month – October, 2025”

  1. jskrypka says:

    So beautifully detailed! The photos and commentary are invaluable to me as I plan to build the same guitar. Kudos to Solo for choosing an acoustic for this month’s guitar.

Leave a Reply